JOE  CELL  KIT  PARTS  NOW  AVAILABLE
FROM - Nutech 2000    http://www.nutech2000.com
HOME
NEW PRESS FIT CONE - This new cone has an apex angle of 57 deg. as described in 'EXPERIMENTER'S GUIDE TO THE JOE CELL'.
Simply 'press on' and seal with 'Sicaflex 291 maine grade $20 supplied'. 
Heat treated to remove any paramagnetism. 
     4 inch 'PRESS ON CONE WITH 5/8" OR 1" EXIT TUBE       $120
     5 inch 'PRESS ON CONE WITH 5/8" OR 1" EXIT TUBE       $130
We now have a low profile 22 deg cone for height restrictions - Add $20 extra an note in the memo
FOUR INCH OUTER CANNISTER - We can supply to suit a set of 8" inner cell tubes and 5" inner cell tubes. The 4" outer tube has an END CAP professionally welded and polished finish. The base is drilled ready to fit your 'CATHODE STUD ASSEMBLY'. Heat treated. 
     10 inch 'OUTER CANNISTER' ( Suits 8" inner tubes )      $ 140
       7 inch 'OUTER CANNISTER' ( Suits 5" inner tubes )      $ 130
 FIVE INCH OUTER CANNISTER - We can supply to suit a set of 8" inner cell tubes and 5" inner cell tubes. The 5" outer tube has an END CAP professionally welded and polished finish. The base is drilled ready to fit your 'CATHODE STUD ASSEMBLY'. The cannister is heat treated. 
     10 inch 'OUTER CANNISTER' ( Suits 8" inner tubes )      $ 150
       7 inch 'OUTER CANNISTER' ( Suits 5" inner tubes )      $ 143
Here you see the 'PRESS ON CONE' and the 'OUTER CANNISTER'. The inside of the Cannister is a polished finish and no visible weld seams where the 'END CAP' has been welded to the 'OUTER TUBE' forming the 'JOE CELL CANNISTER'
We have sought the most simple way to construct the 'Joe Cell' in accord with all the design characteristics required for a functional 'JOE CELL'. This design is economical for the experimetor who cannot construct the hardware him self.
4" CANNISTER  INNER TUBES - 1", 2"& 3"Diameter Tubes.
Sets come in two lengths - 5 inch and 8 inches. Each tube is machined on each end for precision. Heat treated to reduce seam magnetism to a minimum. 
        5 inch high cell set ( machined + Heat treated but not polished )    $ 70 
        8 inch high cell set ( machined + Heat treated but not polished )    $ 75 
'CHARGING CELL KIT' - 1", 2", 3", 4"and 5" Diameter Tubes.
This set is ideal for the Water Charging cell. See notes in shopping trolley. Each tube is  precision machined and heat treated to reduce seam magnetism in the tubing. 
Mount your 'CHARGING CELL' in a glass beaker.You need to drill the bottom of the beaker with a 1/2" hole.  See manuals.
 We can supply a PVC  6" END CAP drilled and ready to mount the charge cell with rubber mat -   $38

         5 inch high cell set ( machined + Heat treatedbut not polished )    $ 175
 
THE CATHODE AND STUD ARRANGEMENT - In this design we machine down the BIG NUT sitting on top of the cathode tube. Allow 3 thou over size for a press fit. We use seamless 316L so heat treating is not necessary. Position nut according to manuals. The stud arrangement is permanently fitted to the BASE of the CANNISTER and you simply unscrew the 'whole Inner Tube Assembly' for cleaning and servicing. 
    The nut is machined and Press Fitted into the Cathode tube. If it were to come loose, a touch of Tig     welding or Silver Solder will secure the nut permanently.
THE CATHODE STUD KIT - Consists of 4.5 " long 316 Stainless whitworth Thread. 
- A BIG NUT to be fitted to the CATHODE TUBE. 
- EBONITE SPACER - to raise the inner tube assembly to the correct position 
- The large white Acetyl disk is machined to fit in the base hole in the bottom of the CANNISTER.  Simply seal with SIKAFLEX ( Marine grade 291 - Can supply for $20 ) 
-Two NUTS and WASHERS and electrical connection are supplied         $57.00 
THE CATHODE STUD KIT ASSEMBLY - The above componants are all screwed onto the stud in their correct order. An electrical CRIMP TERMINAL with 12" of whire is also supplied but not shown. A plumbers PVC END CAP makes an ideal base to mount the cell on.Nut is press fitted in the Cathode 
    
     The CATHODE STUD KIT with ELECTRICEL CONNECTOR - $57

EBONITE SPACER ROD - This is an excellent material to use between the cell plates. It is totally non reactive to electrical and magnetic fields. Allow 3/4 inch length for each spacer. Six Spacers for each cell gap. You can calculate how many you will need or we can calculate the length and cahrge accordingly. 
              16"  per CHARGE CELL    16" per 5" dia cell. 12" per 4" cell
      EBONITE ROD - $28 includes 3 rubber stoppers for outer tube support to cannister.

     Nutech 2000
     P.O. Box 8
   HEIDELBERG WEST.Vic.3081
        Australia
 nutech@tpg.com.au

     PLACE ORDER ON 
       OUR WEB SITE
The 'Joe Cell Phenomenon' is a truely remarkable technology that is right at the frontier of NEW SCIENCE..There are many dedicated experimenters that are slowy bringing this technology to a more 'user friendly reality'. We are all on a learning curve which has only just begun, but the great thing is that the ordinary person can actually replicate this remarkable new energy source. ORGONE ENERGY ? - Call it what you want, but it is real and in reach. MANY FOLK ACROSS THE WORLD HAVE REPORTED MANY SUCCESS STORIES ranging from drastically effecting the engine to actually TOTALLY RUNNING ON THE CELL. Keep in mind that the WATER is also a key componant in the running of the cell. See the 'water books' in the 'JOE CELL' section on the 'SHOPPINH TROLLEY'. If you think water is 'just water', then you better think again and get hold of these books. Water is the 'KEY' to to life and the Bio-energy field all around us.
    DISCLAIMER These parts are made available for the convenience of 'JOE CELL EXPERIMENTERS' who are unable to obtain or construct the componants according to the manuals them selves. Please be aware that any such experiments can be dangerous and we advise you to take all possible safety precautions. The purchaser or end user of any ideas, plans or parts obtained from Nutech 2000, must ACCEPT FULL AND TOTAL RESPONSIBILITY AND LIABILITY for ANY DAMAGE to PERSON or PROPERTY that may result from any form of experiment or application of the hardware. 
We will replace componants if not made to our specification or as advertised. We make no guarantee as to the performance of any hardware sold. But always ready to assist where possible.